Showing results: 2746 - 2760 of 2950 items found.
-
NI
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
G5.DT -
Regatron AG
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
Microchip Technology Inc.
Achieving highly accurate precision timing is no easy feat from a technology perspective, so it’s important to find a resource you can trust to reduce design risk and speed your time to market. Our end-to-end timing solutions generate, distribute and apply precise time for multiple industries, including communications, aerospace and defense, IT infrastructure, financial services, power utilities and more. We provide a broad range of clock and timing solutions ranging from MEMS oscillators to active hydrogen masers. Explore our portfolio of clock and timing components and systems to find the right solution for your project.
-
CXAR/256-MF -
Cytec Corp.
This Chassis is intended to control up to eight 16x1 solid state 75 ohm cable TV modules, or may be used to control a great number of 8x1, 4x1, 2x1 or 2x2 modules. It is often used to control a large variety of custom configurations which may be located in separate chassis. When used as a separate driver chassis it can control up to 256 switch points from a 2 RU chassis. LEDs on the front panel show switch and power status. Add Switch Modules, CP16 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
Agilent Technologies
The MassHunter software suite supports efficient data acquisition, qualitative data analysis, mass spectral library management, quantitative data analysis, easy access, and reporting for Agilent GC/MS and LC/MS systems.Data acquisition software for GC/MS and LC/MS allows straightforward setup and operation of the entire system, while powerful data analysis software and application-specific software tools streamline the analysis workflow for any sample task. Powerful library management software with extensive curated libraries and databases for Q-TOF instruments facilitates unknowns identification. Finally, simplified software interfaces for mass spectrometry provide access to the power of mass spectrometry to anyone.
-
WMA-005 And WMA-005LF -
Falco Systems
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
WMA-01 And WMA-01LF -
Falco Systems
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
WMA-02 And WMA-02LF -
Falco Systems
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
230 -
Electronic Specialties Inc.
Short Buddy helps you find the short! This unique tool connects at the fuse panel and becomes in series with the test circuit. A system of audible beeps helps you find the problem and permit hands free troubleshooting. Have a dead short? Short Buddy gives you continuous re-set/re-power capability, a real time saver. While you push, pull, tug and grab wires, Short Buddy is always watching the current level. If your tug causes the dead short again, Short Buddy opens the circuit for 10 seconds, then re-applies power to the circuit. Re-powering the circuit can also be done manually.
-
784959-01 -
NI
The IC‑3120 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3120 offers two Gigabit Ethernet ports with Power over Ethernet (PoE) technology, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
N6784A -
Keysight Technologies
The Keysight N6784A is a source/measure unit (SMU) designed for general-purpose precision sourcing and measurement. General-purpose applications can span many different industries and many different devices under test (DUTs). The N6784A SMU is a versatile tool designed to tackle many of these general-purpose applications. Its glitch-free operation ensures safe usage with the DUT during output and measurement range changes, even with capacitances of up to 150 µF. Its 4-quadrant operation enables it to act as a bipolar power supply or a bipolar electronic load, for added versatility. When using the N6784A SMU, engineers can be confident that they have an all-around general-purpose tool for their test systems or lab bench.
-
Model 302 -
Rinch Industrial Co.,Limited
1. Time,date display.2. Time alarm clock every day.3. 12/24 hours system clock.4. ℃/℉ temperature display.5. Relative humidity and comfort display.6. Temperature and relative humidity trend display.7. Max/Min Temperature and relative humidity display.8. Temperature measure range: -20℃~50℃9. Temperature resolution: 0.1℃10. Temperature accuracy: ±1℃11. Humidity measure range: 10%~95%RH12. Humidity resolution: 1%13. Humidity accuracy: ±5%RH14. Measuring period: 20 sec15. Power: 1.5V (AAA or 7# battery)
-
NI
The Analog Output Device helps you create applications such as stimulus-response, power supply control, deterministic control, and sensor/signal simulation. The Analog Output Device supports various output resolutions, channel counts, and other onboard features, so you can replace several kinds of instruments in your system, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.The Analog Output Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
MS 1727 -
Meltronics Systemtech
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
